How to flash Android 4.4.2 N900XXUDNA6 for Galaxy Note 3 N900: ~ ALL MOBILE SOLUTIONS

Download the N900XXUDNA6 firmware zip from here or here.
After the download is complete you need to unzip the archived contents.
– you will get the N900XXUDNA6_N900SERDNA6_N900XXUDNA1_HOME.tar.md5 file.
– do not extract any further than that.
Download Odin3 v3.09 from here.
– extract the contents of this zip.
Power off your Note 3 now.
Boot the phone in Android Download Mode.
– if you don’t know how to boot Download Mode, then you can find help here.
Launch Odin 3.09 exe on your computer.
Now use the USB cable and connect the Note 3 with your PC.
– wait for Odin to detect the phone, then you can continue to the next step.
> if the phone is not detected by Odin, then it would be best for you to re-install the Samsung USB Drivers.
> when everything is set and the phone was recognized you can get to the next step.
Go to Odin, click the AP button and then load the N900XXUDNA6_N900SERDNA6_N900XXUDNA1_HOME.tar.md5
file.
> make sure that the Re-Partition option is not enabled.
> don’t change other default Odin settings.
Press the START button when you’re ready to begin the installation of Android 4.4.2 update on your Galaxy Note 3 Exynos.
> don’t press any buttons until the process is complete.
When the installation is finished you will see that ODIN displays the ‘PASS’ alert, while the phone reboots in normal mode.
– disconnect the phone from PC when the Note 3 boot animation screen appears.
Wait for the Note 3 to load the new home screen and after that you can begin testing all the new features.

These were all the steps that you had to follow in order to successfully update your smartphone. If the installation was successful, then you can close this guide and start testing / customizing the Android 4.4.2 KitKat OS. If you’ve encountered problems during installation, read the ‘notes’ below.
NOTE 1: If Odin freezes, closes unexpectedly or the phone gets blocked, then you will be forced to repeat the entire tutorial once again. Make sure that you won’t skip any steps that I’ve listed above and ask for help in comments.
NOTE 2: If Odin completes installation, but the phone doesn’t go past the Samsung Galaxy Note 3 animation, then you will have to apply a ‘factory reset’. This process will remove all data from system partition, but it will force the Note 3 to boot in normal mode. Here’s how to do that:

power off the phone completely.
boot it in Stock Recovery Mode.
– it can be done by pressing and holding Volume Up, Home and Power at the same time.
– release the buttons when the Recovery Mode menu appears.
select ‘wipe data/ factory reset’, confirm.
when the process is complete you need to select ‘reboot system now’ and wait for the boot to complete.

Samsung N900 Latest Firmwares Android 4.3 Phone Model Samsung N900 Phone Name Samsung Samsung Glaxy Note3 Firmware Flash Tutoriall(How To Flash Samsung Glaxy Note 3) Model Code: SM-N900 Model Name: GALAXY Note 3 Country: Russia Android OS Version: Android 4.4.2 KitKat Changelist: 1955999 Build date: Mon, 23 Jun 2014 12:07:20 +0000 Product Code: SER PDA: N900XXUENF3 CSC: N900SERENF2 MODEM: N900XXUENF2 Download The Following Files and Programs: Odin3 Flasher. Samsung Galaxy Note 3 SM-N900 USB Driver. N900XXUENF3 Firmware Update Package. Preparation Steps: 1- Download Odin3 flasher and extract it. 2- Extract the N900XXUENF3 Firmware Update Package. 3- Download and install the Samsung Galaxy Note 3 USB driver. 4- Restart your Computer. 5- Backup any wanted data on your device. 6- Charge your Note 3 battery to be at 80% minimum. 7- It is better to make Factory Data Reset, That can keep you away from some errors later. 8- Enable USB debugging option. Installing XXUENF3 Android 4.4.2 KitKat Update on your Galaxy Note 3 SM-N900: 1- Turn off your device, And take out its SIM and Memory card. 2- Put your Galaxy Note 3 into Download Mode. 3- Connect it to your Computer using the USB cable. 4- Wait for a couple of seconds to let your PC recognize the connected device. 5- Run Odin3.exe flasher as Administrator. 6- Make sure that Re-Partition option is not checked. 7- If Odin3 flasher detects your Galaxy Note 3 correctly, You will see its COM port number 0:[COMxx] 8- Click on AP button and select: N900XXUENF3_N900SERENF2_N900XXUENF2_HOME.tar.md5 9- Click on Start button, Odin3 will begin to install the new firmware on your Galaxy Note 3. 10- After the installing is done, Your Galaxy Note 3 will be rebooted automatically. 11- When your device is on again, Disconnect it from your PC. 12- Wait until it is completely on, Then check the new installed firmware. 13- Done, Congratulations, You have installed the new XXUENF3 firmware version on your Galaxy Note 3 SM-N900. N900UBUCMK1 / UUBCMK1 Argentina Download N900UBUCMK1 / PSNCML1 Argentina Personal Download N900UBUCMK1 / TFGCML1 UFN Argentina Movistar Download N900XXUCMK2 / ODDCMK1 India Download N900XXUCMK2 / SERCMK1 Russia Download N900XXUCMK2 / OLBCMJ3 Southeast Asia Download N9000QXXUCMK2 / QTURCMJ3 Turkey La Fleur Download N900XXUCMK2 / OJVCMJ3 XSG United Arab Emirates Download Samsung Glaxy note 3 Driver Download Download Done, Congratulations, You have installed the new XXUENF3 firmware version on your Galaxy Note 3 SM-N900.

Copy and WIN : http://ow.ly/KNICZ

ALL MOBILE SOLUTIONS

Thursday 9 July 2015

How to flash Android 4.4.2 N900XXUDNA6 for Galaxy Note 3 N900:

0 comments:

Post a Comment

Categories

Flash File

Flash Box

Mobile Price

Hard Reset

Page Views

Fan Fages

Contact Form

About Me